ZLINK Q7-1500 Automated Guided Vehicle

ZLINK Q7-1500 overview

The ZLINK Q7-1500 is a 1,500 kg rated-load automated guided vehicle in the ZL Series. The manufacturer's application scope covers warehouse logistics and production line material handling, including wet wipes manufacturing. Its combination of rated load and vehicle dimensions makes it a distinct selection alongside the family's fork-type Folklift.

Although both models share a 1,500 kg rating, their published geometry is different. The Q7-1500 should therefore be evaluated as its own configuration rather than treated as an interchangeable substitute. A project review must establish the load interface, route requirements and station arrangement appropriate to the intended material movement.

Design and movement envelope

Dimensions for higher-load projects

The Q7-1500 measures 1,110 mm long, 860 mm wide and 315 mm high, with a machine mass of 317 kg. These are vehicle dimensions, not the dimensions of a complete loaded assembly. Any carrier, fixture or overhanging material needs its own clearance assessment.

The technical table specifies a 637 mm turning radius and a 1,500 mm minimum right-angle passing width. The manufacturer's family FAQ uses 1,500 mm in its turning discussion, but the model-specific technical entries distinguish the two measurements. Layout planning should preserve that distinction and confirm the proposed loaded maneuver with the supplier.

Navigation and positioning technology

The listed navigation method is LSLAM/QR code navigation, paired with differential drive and a touch screen HMI. Model-specific positioning accuracy is ±20 mm and ±2°. This differs from the ±10 mm and ±1° figures listed for the other three models, so family-level accuracy statements should not be substituted for the Q7-1500 specification.

Assess the stated accuracy against the actual task. If a load must meet a constrained transfer location, agree how alignment will be checked and what installed performance is required. The published navigation entry does not establish every commissioning detail or a particular integration interface.

Technical specifications

The lifting values use the manufacturer's hc and h2-h3 designations. Their reference geometry needs confirmation before selecting station heights. Do not combine the two figures into an assumed lift range or use them to infer a particular load attachment.

Applications and material-flow planning

The Q7-1500 can be considered for projects whose required transported mass falls within its published rating and whose load arrangement is confirmed compatible. Candidate tasks within ZLINK's stated scope include transfers between warehouse staging and production areas. These examples are selection discussions, not confirmation that a particular carrier or station is supplied.

In wet wipes manufacturing, identify what is being moved, how it is supported and how each destination receives it. Product type alone does not determine suitability. Record the complete transported assembly, load distribution and pickup conditions so the supplier can assess the handling arrangement against the required capacity and geometry.

Integration and operational considerations

A higher rated load does not remove the need for detailed route assessment. Review floor conditions, turns, station approaches and the interaction between the loaded vehicle and surrounding activity. The required risk assessment, operating procedures and any protective equipment should be agreed for the site; the source does not verify a specific safety hardware package.

Where an installation needs automated task dispatch or production-system coordination, request a controls proposal. No particular software API, connectivity method or warehouse-system compatibility is established by the available technical data. Define these as project requirements rather than assuming them to be standard functions.

Battery and charging review

The specified battery is rated at 48 V and 24 Ah. Automatic and manual charging are listed. ZLINK's family FAQ describes 6–8 hours of operation and recharge periods of up to 1.5–2 hours depending on model. Confirm an operating and charging schedule for the proposed duty cycle instead of treating those family figures as a guaranteed shift result.

Pricing and availability

The source does not establish a published retail price. Pricing depends on model and configuration, so a quotation should define the Q7-1500 arrangement, required interfaces and project responsibilities. Supply the route plan, load information and transfer requirements to make the proposal specific enough for technical comparison.

Availability is subject to confirmation, and no supplier stock position is established here. Confirm delivery terms, commissioning scope and the final specification before setting project milestones around the vehicle.

Frequently asked questions

What load rating is published for the Q7-1500?

The model has a 1,500 kg rated load. Compatibility still depends on the actual load arrangement and transfer requirements.

Is its turning radius 1,500 mm?

The technical table gives a 637 mm turning radius. The 1,500 mm figure is the minimum right-angle passing width.

Does it share the other models' positioning accuracy?

No. The Q7-1500 table entry states ±20 mm and ±2°, rather than ±10 mm and ±1°.

What battery and charging methods are listed?

A 48 V, 24 Ah battery is specified, with both automatic and manual charging.

Is it equivalent to the Folklift?

No. The two share a rated load, but their dimensions and published model descriptions differ. Confirm the required load-handling configuration separately.

Summary

The ZLINK Q7-1500 combines a 1,500 kg rated load with a 1,110 × 860 × 315 mm vehicle envelope. Its defining planning references include a 637 mm turning radius, 1,500 mm right-angle passing width and model-specific ±20 mm/±2° positioning accuracy.